Coverage Explained

Metal Roofing Contractor Insurance in Texas: Coverage and Requirements

A pneumatic coil nailer and a claw hammer resting on shingle courses, chalk lines snapped across the deck

Insurance for a Texas metal roofing contractor turns first on a choice: the Texas Department of Insurance says private employers can choose whether to carry workers’ compensation. The Labor Code attaches real consequences to going without it, public construction contracts require it, and general liability, auto and equipment coverage then follow the panel work.

The Texas workers’ comp choice

Texas is the state where a roofing contractor’s first insurance question is not “which policy” but “will I carry it.” The Texas Department of Insurance says private employers can choose whether to provide workers’ compensation insurance coverage. The Texas Labor Code says the same thing in its own words: except for public employers, an employer may elect to obtain workers’ compensation insurance coverage.

Employers that choose not to are known as non-subscribers. Those that do carry it obtain coverage, the department says, by purchasing coverage through an insurance carrier. The post on who offers workers’ comp for roofing contractors explains how a roofer gets placed, and the post on Houston roofing workers’ comp rates covers what drives the price for a Texas crew.

For a metal roofer whose crews handle long panels at height, the choice deserves a careful look rather than a default. The sections below explain why.

It also helps to separate the two questions an owner can blur together. The first is legal: what the Labor Code allows and what it takes away. The second is practical: who pays for a crew member’s medical care and lost wages after a fall, and how the company would carry that cost. A workers’ comp policy answers the second question in a defined way. Going without it leaves the answer to the company’s own resources, to any alternative benefit plan it sets up, and to the courts. Neither path is free of cost, so put the comparison on paper with your advisor and your attorney before a claim forces it.

What the Labor Code says about going without it

The Texas Labor Code takes away specific defenses from an employer when an employee who is not covered by workers’ compensation insurance sues. In that action, the code says the employer may not defend on the grounds that the employee was guilty of contributory negligence, that the employee assumed the risk of injury or death, or that the injury or death was caused by the negligence of a fellow employee.

Those are the defenses an employer might otherwise reach for after a fall from a metal roof: the worker was careless, the worker knew the roof was slick, another crew member left a panel loose. Without workers’ comp, the code removes them from the table. That is a question for an attorney, and it is one to ask before an injury, not after.

Non-subscribers also have duties. The Texas Department of Insurance says they should give written notice of no coverage to new employees, post a notice of no coverage in the workplace, and file a notice of no coverage with the Division of Workers’ Compensation during the filing period the department sets. The department adds that employers who opt out must notify their employees and the division. The workers’ compensation coverage page explains what the policy does for a crew, which is the other side of the comparison.

Public jobs and contracts that require coverage

The choice narrows on public work. The Texas Labor Code says a governmental entity that enters into a building or construction contract shall require the contractor to certify in writing that it provides workers’ compensation coverage for each of its employees on the project. A metal roofer bidding a school gymnasium, a county maintenance building or a city fire station should expect the bid documents to ask for proof.

Private contracts can ask too. General contractors, property managers and commercial owners can write workers’ comp, specific limits and endorsements into the insurance exhibit whatever the statute allows. Send that exhibit to your agent before you sign, and ask whether your current program meets it. A metal roofer working as a subcontractor on a commercial project can also be asked for additional insured status, a waiver of subrogation or primary and noncontributory wording, and each of those is an endorsement that has to be arranged in advance rather than promised on a certificate. The Texas location page covers how these requests show up across the state.

Real-World Scenario: A Texas metal roofing contractor has run as a non-subscriber for years, working on shops and barns for private owners. A general contractor invites the company to bid the metal roof on a public school addition. The bid package asks for written certification of workers’ comp coverage for the crew on the project. The owner calls the agent, learns what it takes to place a policy on short notice, and decides with an attorney whether to change course for public work.

How a Texas roofing comp premium is built

If you carry the coverage, the Texas Department of Insurance describes how the premium is put together. Texas employers are assigned one or more classifications based on the type of business, and each employee’s payroll is then assigned to the appropriate classification. An experience rating modifier that reflects the employer’s past loss history may be applied to the premium.

For a metal roofer, the practical point is accuracy. A company that installs metal roofs and also does sheet metal fabrication in a shop, sells panels or runs a separate gutter crew has more than one kind of work, and the payroll should be described that way. The post on roofing workers’ comp class codes explains how classification works, and getting it right at the start is easier than arguing about it at the audit.

Texas metal roofer decision path A vertical stack of blocks for Texas metal roofing contractors: the choice between being a subscriber or a non-subscriber, made with an attorney; what going without coverage means, including lawsuit defenses removed and required notices and filing; where coverage is required, on public building contracts and private contracts that ask for it; and metal panel exposures such as wind on panels, sharp edges and leaking seams and fasteners. A closing band says to list roll formers and panels before the job. No figures or dollar amounts are shown. Texas metal roofers: the comp decision first Subscriber or non-subscriber Private employers may choose Decide with an attorney What going without means Some lawsuit defenses removed Notices and a filing required Where coverage is required Public building contracts Private contracts that ask Metal panel exposures Wind on panels, sharp edges Seams and fasteners that leak List roll formers and panels before the job, not after
In Texas the workers’ comp decision comes first, and the metal panel work shapes everything that follows.

What metal panels add to the risk

Metal roofing changes the exposure in ways an underwriter will want to hear about. None of this is a Texas legal requirement. It is general insurance explanation.

On the job, long panels act like sails when they are lifted and set, and a gust can turn a carried panel into a cause of injury or of damage to a vehicle or building below. Panel edges and trimmed offcuts can cut. Finished metal can be slick with dew, dust or rain, which bears on fall exposure. Some details call for soldering or other heat, and any flame or spark on a roof raises the hot work question covered in the post on torch-down and hot work fire risk.

After the job, the completed operations exposure shows up where metal roofs are vulnerable: fasteners that back out, seams that open, flashing at penetrations, and attachment that does not hold in wind. Hail can dent a panel without causing a leak, and the difference between cosmetic and functional damage can become a dispute with a customer. The post on whether general liability covers a roof leak explains how that coverage responds, and the general liability coverage page covers the policy in full.

Roll formers, stored panels and equipment

Metal roofers can own equipment other roofers do not, including portable roll formers, seamers, brakes and shears, and they can store large quantities of panels and trim at a job site before installation. Equipment that moves between jobs belongs on an equipment schedule, and the contractors equipment page explains how that coverage works. Panels and materials sitting at a site before they are installed raise an installation floater question to ask us about, because the answer depends on the policy and the contract.

The specialty metal and tile roofing page and the commercial and industrial roofing page describe how residential and commercial metal work is presented to underwriters. Larger commercial contracts can also ask for an umbrella, which the post on umbrella and excess coverage explains.

Questions to ask before your Texas renewal

  • Are we a subscriber or a non-subscriber, and have we put that decision in writing with an attorney?
  • If we are a non-subscriber, have we given and posted the notices and made the filing the department describes?
  • Do any public or private contracts we are bidding require workers’ comp for our crew?
  • Is our payroll split by the kinds of work we do, including shop fabrication or gutter work?
  • Are our roll formers, seamers and trailers listed on the equipment policy?
  • What happens if panels stored at a job site are stolen or damaged before installation?

The Texas cost guide explains what moves a roofing premium in the state. When you are ready to compare options, start on the quote page.

Sources: the Texas Department of Insurance’s coverage page, non-subscriber page and workers’ compensation rate guide, and the Texas Labor Code chapter on workers’ compensation insurance coverage. This post is general education, not legal or tax advice.

The bottom line

A Texas metal roofing contractor faces a decision of its own: the Texas Department of Insurance says private employers can choose whether to carry workers’ compensation. The Texas Labor Code takes certain defenses away from an employer without coverage when an injured employee sues, and requires a contractor on a public building or construction contract to certify coverage for its employees on the project. Around that decision, liability, auto and equipment coverage should describe metal panel work as it is actually done. This post is general education, not legal or tax advice.

Frequently asked questions

Do metal roofing contractors in Texas have to carry workers’ comp?

Not always. The Texas Department of Insurance says private employers can choose whether to provide workers’ compensation coverage, and employers that choose not to are called non-subscribers. That choice has legal consequences, public construction contracts require the coverage, and private contracts can require it too. Make the decision with an advisor and an attorney rather than treating either answer as the default.

What does a Texas roofer give up by going without workers’ comp?

Certain defenses in an injury lawsuit. The Texas Labor Code says that in an action by an employee who is not covered by workers’ compensation insurance, the employer cannot defend on the grounds that the employee was guilty of contributory negligence, assumed the risk of injury or death, or was hurt by a fellow employee’s negligence. Ask an attorney how that applies to your crew.

Do I need workers’ comp for a public roofing job in Texas?

Yes, for a building or construction contract with a governmental entity. The Texas Labor Code says a governmental entity that enters into such a contract shall require the contractor to certify in writing that it provides workers’ compensation coverage for its employees on the project. Read the bid documents early, because the proof is part of being awarded and keeping the job.

What must a Texas non-subscriber roofer do?

Give notice. The Texas Department of Insurance says non-subscribers should give written notice of no coverage to new employees, post a notice of no coverage in the workplace, and file a notice of no coverage with the Division of Workers’ Compensation during the filing period the department sets. The department’s non-subscriber page lists the steps, and your attorney can review them with you.

How is a Texas roofing workers’ comp premium built?

From classification, payroll and history. The Texas Department of Insurance says employers are assigned one or more classifications based on the type of business, each employee’s payroll is assigned to the appropriate classification, and an experience rating modifier reflecting past losses may be applied. Describe metal roofing work accurately so the payroll lands in the right place before the audit.

What exposures does metal roofing add?

Panel handling, edges and wind. Long metal panels can catch wind while they are lifted and set, edges can cut, and finished surfaces can be slick. After the job, leaks at fasteners, seams and penetrations are the completed operations concern. Roll-forming equipment and stored panels raise equipment and installation questions to ask us about. These are general insurance points, not Texas requirements.

About the author

Nate Jones, CPCU

Nate Jones, CPCU, is the founder of Wexford Insurance and Roofing Guard Insurance, a specialty insurance agency placing roofing contractor coverage in 48 states across a 16-carrier specialty panel. He places insurance for Texas roofing contractors, including metal roofers working standing seam and exposed-fastener systems on homes, shops and commercial buildings, and he reads the Texas Department of Insurance pages and the Labor Code before he explains the workers’ comp decision. This page keeps to what those official sources say and treats the rest as general insurance explanation. Connect via the Roofing Guard Insurance quote form or call 317-942-0549.

Insure your roofing operation with a CPCU-led agency

Tell us how you work — residential steep-slope, commercial and industrial low-slope and torch-down, or specialty metal and tile — and we will market it to carriers that write the roofing class.